1.) TONING & BLENDING2.07 - TONING & BLENDING
After lighting the actor with AREA LIGHTING, it may or may not be necessary to provide additional light to the surrounding scenery. Usually lighting specifically used to light the scenery is referred to as 'toning and blending' lighting - as it helps tone the scenery and blend with the acting area lighting.
Sometimes, for example when lighting a drama, in a box set, only area lighting may be required. No additional lighting is needed to light the set. This is due to the fact that reflection from the area lighting may bounce off the floor and illuminate the walls in a most naturalistic and appropriate way.
Alternately, however, if the production is a comedy, the set may feel a bit dark and dreary. No matter how the lighting designer tries to boost the acting area lights, the set still looks dark in comparison. In this case, additional lighting of the upper walls of the box set would probably provide an appropriate visual lift.
2.) TONING & BLENDING - FIXTURES
Toning and blending lighting, tend to use different fixture types, depending on the exact lighting application. Spotlights, floodlights and striplights all have their place.
3.) TONING & BLENDING - METHODS
Often toning and blending lighting is provided by soft flood type of fixtures. Both strip lights and box floods are suitable for this application.
Alternately spotlights may provide a more dramatic form of toning and blending. I personally like to use ellipsoidal reflectors with soft focus break-up templates to provide a textured toning and blending light to each wall of a set. These fixtures are usually located at a fairly low angle (box booms), and gently 'wash' and tone the scenery as needed.
During the early 1900's and until about 1960, toning and blending lighting was often provided from a series of three (3) or four (4) color strip lights, mounted above the stage. Strips (also called X-RAYS) ran from stage left to stage right, and were often used; downstage, center stage and upstage. Some theatres might have as many as five (5) sets of strip lights, permanently installed. Strip lights typically would be colored with glass or plastic filters in; red, green, blue and amber. Musicals, operas and variety shows, found strip lighting particularly useful in providing color washes. One moment the stage could be completely bathed in a night blue, the next in daytime amber. The red, green, blue, primary filters allowed just about any color to be mixed to provide an instant color wash to the stage, or the scenery below.
Sometimes, for example when lighting a drama, in a box set, only area lighting may be required. No additional lighting is needed to light the set. This is due to the fact that reflection from the area lighting may bounce off the floor and illuminate the walls in a most naturalistic and appropriate way.
Alternately, however, if the production is a comedy, the set may feel a bit dark and dreary. No matter how the lighting designer tries to boost the acting area lights, the set still looks dark in comparison. In this case, additional lighting of the upper walls of the box set would probably provide an appropriate visual lift.
2.) TONING & BLENDING - FIXTURES
Toning and blending lighting, tend to use different fixture types, depending on the exact lighting application. Spotlights, floodlights and striplights all have their place.
3.) TONING & BLENDING - METHODS
Often toning and blending lighting is provided by soft flood type of fixtures. Both strip lights and box floods are suitable for this application.
Alternately spotlights may provide a more dramatic form of toning and blending. I personally like to use ellipsoidal reflectors with soft focus break-up templates to provide a textured toning and blending light to each wall of a set. These fixtures are usually located at a fairly low angle (box booms), and gently 'wash' and tone the scenery as needed.
During the early 1900's and until about 1960, toning and blending lighting was often provided from a series of three (3) or four (4) color strip lights, mounted above the stage. Strips (also called X-RAYS) ran from stage left to stage right, and were often used; downstage, center stage and upstage. Some theatres might have as many as five (5) sets of strip lights, permanently installed. Strip lights typically would be colored with glass or plastic filters in; red, green, blue and amber. Musicals, operas and variety shows, found strip lighting particularly useful in providing color washes. One moment the stage could be completely bathed in a night blue, the next in daytime amber. The red, green, blue, primary filters allowed just about any color to be mixed to provide an instant color wash to the stage, or the scenery below.
No comments:
Post a Comment